Using a power strip, surge protector or a wall outlet switch to turn the printer on and off may cause premature failure. The Power light comes on and the Print Cartridge light blinks.
Note: Be sure not to touch the ink nozzles or the copper electrical contacts. Also, do NOT remove the copper strip; these are electrical contacts required for proper operation of the print cartridges. With the copper electrical contacts toward the rear of the printer and the print cartridge held vertically, push the print cartridge firmly down into the appropriate cradle.
Insert the black print cartridge in the right cradle, and insert the tri-color print cartridge in the left cradle. You must insert both print cartridges for the printer to operate. The Print Cartridge light continues to blink for awhile and then goes off. When a print cartridge starts to run out of ink, replace it. If you do not have a replacement, leave the empty print cartridge in the cradle of the printer.
The printer will not print with only one print cartridge installed. We recommend you keep spare print cartridges on hand. When buying print cartridges, check the part numbers referenced below carefully to make sure you are buying the right print cartridges for your printer.
These print cartridges have been specifically designed to work with your printer to produce results that are always clear, always sharp. Black HP No. Tri-Color HP No. Make sure all the paper in the stack is the same size and type. Tap the stack on a flat surface to even it up. Make sure the paper lies flat in the tray and that the paper fits under the tab of the paper-length adjuster. Before you can use your new HP DeskJet printer, you must install the printer software on the computer from which you will print.
Your printer software is located on the CD included with your printer. From time to time, Hewlett-Packard provides updated printer software.
See page 26 for instructions on how to close software programs. For Windows 95 , 98 , and NT 4. From the taskbar, select Start Run.
Click OK. For Windows 3. In the Program Manger, select File Run. Your printer model number will be on the install button. Then, proceed to step 5. Click Next and proceed to step 5. Note: If you need the printer software on floppy disks:. When the opening screen appears, select Make diskettes of your printer software. Then turn off the computer and the printer. Turn on the printer, then turn on the computer. If you are using a parallel cable for communications between your printer and your computer, see page 3.
USB uses a standard port and plug combination for connecting devices like printers, modems, scanners, and digital cameras. It also offers the benefit of being able to easily add, remove, and move devices. Note: Use only the Power button on the front of the printer to turn the printer on and off.
Using a power strip, surge protector or a call outlet switch to turn the printer on and off may cause premature failure. With the copper electrical contacts toward the rear of the printer and the print cartridge held vertically, push the print cartridge firmly down into the cradle. Note: Make sure the computer is operational, meets the minimum system requirements and that its USB port is enabled and properly configured.
You can still enjoy the full capabilities of your HP DeskJet C Series printer by connecting the printer to the computer with a parallel cable. Do NOT click Next. Click on the win98usb folder then click OK to close the Browse screen and return to the Wizard. The Add New Hardware Wizard searches for the win98usb driver.
If Windows is unable to find a driver, click Back to return to Step 4. Click Next. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. You control settings such as paper size, scaling, page orientation, and watermarks from the HP DeskJet Series Page Setup dialog box. To get to this dialog box:. Make sure you correctly choose the size of paper, envelopes, or other media you have in the IN tray.
Enter a number from 20 to Numbers smaller than reduce the image size, and numbers greater than enlarge it. Changing size may change pagination. You control settings such as number of copies, all or specific pages to print, paper type, print quality, page layout, color, and background printing from the.
General is the default panel selected in the Print dialog box menu. This panel lets you select the number of copies you want to print, whether you want to print the entire document or select pages, and whether you want to print from the front of your document or begin printing from the end forward. Indicate whether you want to start printing from the first page or from the last page.
You may also choose the following options from the General menu:. Choose from a wide range of paper types. Print Quality Draft: Quick printing. Normal: Every day printing. This dialog box allows you to specify the number of pages printed on each sheet of paper, or to print a poster by specifying the number of pages printed across and down.
You also set Two-Sided Printing options from this dialog box. Choose the number of pages 1 , 2 , or 4 to print on each sheet. Choose the size of your poster by choosing the number of pages across and down 2x2 , 3x3 , or. If you check Print Both Sides ,. While you can adjust saturation, brightness, and color tone with the sliders that appear when you choose this option, the center position of the sliders is optimized for most printing uses and types of media.
The ColorSync setting can be used for color matching with other components using the ColorSync matching system. Grayscale prints in shades of gray. With this setting, you also have the option to optimize printing for fax and photocopy. Choose Background if you want to continue working while printing takes place. The following table describes additional features available when using background printing. To access these features from the desktop, double-click the.
Select the job title or icon, then click the Trash icon. Select the job title or icon, then click the Pause button.
Select the job title or icon, then click the small clock. In the dialog box that appears, click Urgent. This moves the. In the dialog box that appears, click At Time , then set the time. From the View menu, choose the title of the column by which. Drag and drop the print job title to the desired place in the list. Choose Stop Print Queue from the Printing menu. Drag the icon for the print request to the icon of the desired. This chapter explains how to use the different printing materials available to you.
Printing Photographs. Printing Greeting Cards and Hagaki. Plain Paper or Inkjet Paper for Hagaki. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. HP Hewlett-Packard. Notice The information contained in this document is subject to change without notice.
Table of Contents Regulatory Notices. The buttons and lights from top to bottom are: Power Button and Light — Use the Power Button to turn the printer on and off. Print Cartridge Status Light — When lit, this light indicates that you need to check the status of your print cartridges. Be sure to slide all media as far as it will go into the IN tray.
Up — For ease of loading media in the IN tray. To select your printer using a USB connection: 1 Make sure the computer and printer are turned on, and your printer is connected to your computer with a USB cable. Checking Printer Status You can tell the status of a printer by looking at its desktop icon: Icon Description Icon Description Idle printer default Printing stopped on default printer Idle printer not default Error on default printer Printing on default printer Printer not available or connected.
To get to this dialog box: 1 Open the software program used to create your document. Paper Size, Scaling, and Page Orientation Make sure you correctly choose the size of paper, envelopes, or other media you have in the IN tray. Click the appropriate icon to choose page orientation. Click to display a list of other printcontrol panels. Enter the number of copies you want to print. Print Quality Draft: Quick printing Normal: Every day printing Best: Highest quality High Resolution Photo: Only for photo media Layout This dialog box allows you to specify the number of pages printed on each sheet of paper, or to print a poster by specifying the number of pages printed across and down.
Check here to print on both sides of the paper. Check to print a border around each page. If you check Print Both Sides , choose appropriate Binding side or top.
These methods delete only the print job, not the document itself. The print request will pause until you select its title again and click the Resume Button. This moves the print request to the top of your print list. This is a good way to save print requests when using a portable computer while away from your printer. You can only view or download manuals with.
0コメント